|
Forums59
Topics1,058,665
Posts14,306,488
Members144,632
| |
Most Online39,925
Dec 30th, 2023
|
|
 Removing rust from table saw
#9856260
03/26/14 04:06 PM
|
Joined: Jan 2010
Posts: 122
tmay
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Jan 2010
Posts: 122 |
What is the best way to do this? I don't think I can get rid of all of but anything would help.
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9856353
03/26/14 04:36 PM
|
Joined: Aug 2013
Posts: 1,494
Harte Nuss
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2013
Posts: 1,494 |
fine sand paper, wd-40, and a rag
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9856539
03/26/14 05:29 PM
|
Joined: Aug 2013
Posts: 1,494
Harte Nuss
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2013
Posts: 1,494 |
oh...then get some wax to cover the top...esp. when not in use...
|
|
|
Re: Removing rust from table saw
[Re: Harte Nuss]
#9856699
03/26/14 06:10 PM
|
Joined: Jan 2010
Posts: 122
tmay
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Jan 2010
Posts: 122 |
how fine? 600-1000 or is that too fine?
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9856736
03/26/14 06:22 PM
|
Joined: Aug 2013
Posts: 1,494
Harte Nuss
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2013
Posts: 1,494 |
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9856937
03/26/14 07:20 PM
|
Joined: Jan 2010
Posts: 122
tmay
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Jan 2010
Posts: 122 |
Thanks for the help. I'll try that tonight.
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9858682
03/27/14 03:16 AM
|
Joined: Jul 2012
Posts: 5,039
Tommar
TFF Celebrity
|
|
TFF Celebrity
Joined: Jul 2012
Posts: 5,039 |
Use automotive paste wax to keep it rust resistant and it helps the wood glide over the top easier when you are cutting.
US Army and TXARNG 1984-2014
Gulf War 90-91
Iraq 2004-05
A'stan 2009
VFW Post Commander 2013-15
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9858916
03/27/14 10:57 AM
|
Joined: Sep 2008
Posts: 121,182
hopalong
Pescador Loco
|
|
Pescador Loco
Joined: Sep 2008
Posts: 121,182 |
use 800 to start and then 1200 to finish, do not use coarser or you scratch the iron.
johnsons paste wax if you can find it is best for surface, 2 coats heavy after sanding.
about to do mine after it got wet moving it down here.
" Hop, set the hook"!
hopalong 99,999
TexDawg 99,999
FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
|
Re: Removing rust from table saw
[Re: Harte Nuss]
#9858917
03/27/14 10:57 AM
|
Joined: Sep 2008
Posts: 121,182
hopalong
Pescador Loco
|
|
Pescador Loco
Joined: Sep 2008
Posts: 121,182 |
" Hop, set the hook"!
hopalong 99,999
TexDawg 99,999
FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9858919
03/27/14 10:58 AM
|
Joined: Sep 2008
Posts: 121,182
hopalong
Pescador Loco
|
|
Pescador Loco
Joined: Sep 2008
Posts: 121,182 |
after I sand I put steel wool (00) on a palm sander and polish it, this helps a lot
" Hop, set the hook"!
hopalong 99,999
TexDawg 99,999
FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9859679
03/27/14 03:47 PM
|
Joined: Aug 2013
Posts: 1,494
Harte Nuss
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2013
Posts: 1,494 |
i've never used over 220 on any of mine and they've been around for years with no scratched up surfaces...but i also do hand sanding, so probably not as rough as a palm sander...i have used a dremel with fine grain for getting inside the tracks tho...
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9862004
03/28/14 12:36 PM
|
Joined: Sep 2008
Posts: 121,182
hopalong
Pescador Loco
|
|
Pescador Loco
Joined: Sep 2008
Posts: 121,182 |
did mine yesterday with some 220 (all I could find) hand sanded and got the rails with a small block. looks good again.
it had a fresh coat of wax when I put it on the trailer so that helped a lot.
delta contractors saw.
" Hop, set the hook"!
hopalong 99,999
TexDawg 99,999
FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9862641
03/28/14 03:38 PM
|
Joined: Aug 2013
Posts: 1,494
Harte Nuss
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2013
Posts: 1,494 |
the delta's are nice...they run a dado better than others i've used...
|
|
|
Re: Removing rust from table saw
[Re: Harte Nuss]
#9863922
03/28/14 11:55 PM
|
Joined: Sep 2008
Posts: 121,182
hopalong
Pescador Loco
|
|
Pescador Loco
Joined: Sep 2008
Posts: 121,182 |
the delta's are nice...they run a dado better than others i've used...  I am about to build some more bge tables again so I need to find a good dado for it.
" Hop, set the hook"!
hopalong 99,999
TexDawg 99,999
FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
|
Re: Removing rust from table saw
[Re: tmay]
#9864171
03/29/14 01:23 AM
|
Joined: Mar 2006
Posts: 9,614
woundedbear
TFF Celebrity
|
|
TFF Celebrity
Joined: Mar 2006
Posts: 9,614 |
I just got a Ryobi 10in from another TFF'r. Wiped it down with some-o-that CLR stuff. Rust came right off. Rinsed it well, dried it with the air hose and waxed it with Johnsons floor wax. Looks really good. About 20 minutes of work. I lit the wax so it was liquid and hot when I applied it.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|
