|
Forums59
Topics1,058,844
Posts14,309,487
Members144,639
| |
Most Online39,925
Dec 30th, 2023
|
|
 Transom saver recommendations?
#702865
04/12/05 03:59 AM
|
Joined: Aug 2002
Posts: 164
KB
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Aug 2002
Posts: 164 |
I am looking for a transom saver as follows: 1) Transom saver is over the roller type with long reach (about 49-53 inches) so most models aren't long enough. 2) Boat is Triton TR-21 with 225 Merc I did find a few on the web that meets my needs but I was curious if anyone had a personal recommendations. Also, anyone tried m-y wedge - http://www.m-ywedge.com ? Thanks, KB
|
|
|
Re: Transom saver recommendations?
#702866
04/12/05 10:02 AM
|
Joined: Jan 2005
Posts: 419
Cajundaddy
Angler
|
|
Angler
Joined: Jan 2005
Posts: 419 |
Some thing is not right with this picture 4 to 4 1/2 foot transon saver?
You sure every thing is set up properly?
I have a 19 1/2' Champion and mine is around 36"
When in doubt set hook!
|
|
|
Re: Transom saver recommendations?
#702867
04/12/05 11:40 AM
|
Joined: May 2003
Posts: 11,586
gary purdy
TFF Guru
|
|
TFF Guru
Joined: May 2003
Posts: 11,586 |
When you get that long, I like to take the ends off and replace the square tubing with 1" hex solid aluminum bar. Done this several times, mostly on Rangers with set back transoms.
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
|
|
|
Re: Transom saver recommendations?
#702868
04/12/05 12:51 PM
|
Joined: Jun 2003
Posts: 32,845
HasBen
TFF Guru
|
|
TFF Guru
Joined: Jun 2003
Posts: 32,845 |
I have used the Loc-n-Stow by Swiveleze for the last couple of years and have been very satisfied. I bought mine at BPS. Give it a look!
โ When you're racing, it's life. Anything that happens before or after is just waiting.โ. Steve McQueen
|
|
|
Re: Transom saver recommendations?
#702869
04/12/05 05:31 PM
|
Joined: Aug 2002
Posts: 164
KB
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Aug 2002
Posts: 164 |
Cajundaddy, Am I sure, heck no.  When I bought my boat new, it came with an extra long transom saver at that time. I believe that the problem is that the roller is well underneath the transom coupled with the fact the the jack plate sets the motor even further back. Gary, Good idea, might be able to build my own from the old pieces. HasBen, Didn't see that one! I had previously looked at their web site - http://www.swivleze.com/ - but couldn't find anything to my liking. However, I did find the Lock 'N Stow at BPS as you suggested. Makes me wonder if Swivl-EZE discontinued it. Might be a good alternative. It would save me from getting on the ground to find the roller to attach the transom saver. If it works well and easier to install, then I am all for it. Thanks everyone. That should get me started... KB
|
|
|
Re: Transom saver recommendations?
#702870
04/12/05 05:33 PM
|
Joined: Feb 2004
Posts: 2,909
coachmas
Extreme Angler
|
|
Extreme Angler
Joined: Feb 2004
Posts: 2,909 |
I have a problem with mine right now. I guess because it is a ranger w/setback transom, I have to extend it way out. Don't know the exact measurements, but i know if the motor turns slightly during towing it puts the saver in a bind. I noticed last week that mine has a crack in the tubing where the v-ed piece goes on the motor. Guess I am going to have to replace it soon. Coach
Wishin I was Fishin!!!
|
|
|
Re: Transom saver recommendations?
#702871
04/12/05 09:27 PM
|
Joined: Jan 2005
Posts: 419
Cajundaddy
Angler
|
|
Angler
Joined: Jan 2005
Posts: 419 |
My question would be is the boat far enough forward on the trailer? I don't care who manufactured the boat and trailer doesnt mean its set up correctly. Also what position is the motor in; I would think some where around 15 to 20 degrees off vertical.
When in doubt set hook!
|
|
|
Re: Transom saver recommendations?
#702872
04/13/05 02:12 PM
|
Joined: Feb 2004
Posts: 2,909
coachmas
Extreme Angler
|
|
Extreme Angler
Joined: Feb 2004
Posts: 2,909 |
Good Point Cajun, That is something I haven't thought about. I just didn't want anything dragging on a speedbump by the ramp. My motor maybe tilted too high. THanks Coach
Wishin I was Fishin!!!
|
|
Moderated by banker-always fishing, chickenman, Derek ๐, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|
