texasfishingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
Jrm17, John Riggle, N.Tx, BrandonDickenson, LostAGoodun
119631 Registered Users
Top Posters(All Time)
TexDawg 124,971
hopalong 121,182
Bigbob_FTW 105,084
Bob Davis 97,224
John175☮ 86,139
Pilothawk 83,932
Mark Perry 74,875
Derek 🐝 68,511
JDavis7873 67,416
Forum Statistics
Forums59
Topics1,058,653
Posts14,306,322
Members144,631
Most Online39,925
Dec 30th, 2023
Print Thread
questions...Merc 9.8 hp, 1969 #3521490 05/29/09 10:40 PM
Joined: Jul 2005
Posts: 122
S
svdk Offline OP
Outdoorsman
OP Offline
Outdoorsman
S
Joined: Jul 2005
Posts: 122
Background...

1969 Merc 9.8 hp 110

Motor last used about 6 years ago...New impeller/tune up, used once or twice and then put in storage 6 years ago. Always ran fine, except lower unit seemed excessively hot to the touch. Restarted today in the tank just fine. Ran for about 5 minutes to check it out.

Questions:

1) is there suposed to be a spray of water, "pee" stream, out the back of the motor? ...there's currently just hot exhaust.

2) occasionally the motor coughs under load. During the cough, exhaust will exit the side of the motor (viewed when cover is off). Is this a significant concern?

Thanks in advance,
Stephen

Re: questions...Merc 9.8 hp, 1969 [Re: svdk] #3521732 05/29/09 11:56 PM
Joined: Jul 2005
Posts: 122
S
svdk Offline OP
Outdoorsman
OP Offline
Outdoorsman
S
Joined: Jul 2005
Posts: 122
OK, I think I found answers to my issues above.


NOW, where can I get parts for a 1969 9.8 hp on Saturday morning...impeller and a exhaust transer gasket?

Re: questions...Merc 9.8 hp, 1969 [Re: svdk] #3521948 05/30/09 01:22 AM
Joined: Nov 2008
Posts: 976
N
NoMinners Offline
Pro Angler
Offline
Pro Angler
N
Joined: Nov 2008
Posts: 976
Nowhere. Go too marine engine.com or Iboats.com

Re: questions...Merc 9.8 hp, 1969 [Re: NoMinners] #3524297 05/30/09 10:35 PM
Joined: Aug 2003
Posts: 683
P
phototom Offline
Pro Angler
Offline
Pro Angler
P
Joined: Aug 2003
Posts: 683
svdk
I once owned a 9.8 merc 110 very strong motor
The pee stream on mine was located on the right side just a little aft of crnter . If you will get under the motor you should be able to see the hole it is flush with the motor housing,mine would stop up a lot I just kept a paper clip handy to clear it out,it did not affect the cooling when it was plugged I believe this is more of a indication that the water pump is working.
Tom H


1991 Tracker TX17
40HP evinrude
Eagle 320 console
Eagle 320 bow
Garmin 72 GPS
[Signature images may not be larger than 600 pixels wide by 125 pixels tall.]
Previous Thread
Index
Next Thread

© 1998-2022 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3