Forums59
Topics1,039,267
Posts13,961,847
Members144,197
|
Most Online39,925 Dec 30th, 2023
|
|
Prop Install
#13350909
11/23/19 11:50 PM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
I installed my new prop. I didn't use a torque wrench.I just tightened it with a wrench. It doesn't use a cotter pin. It has a tab washer. I really don't see what bending the tab up is going to do.
|
|
Re: Prop Install
[Re: Bentman63]
#13350936
11/24/19 12:21 AM
|
Joined: Jan 2009
Posts: 1,649
spankyttx
Extreme Angler
|
Extreme Angler
Joined: Jan 2009
Posts: 1,649 |
it's a lock, the tabs will bend up on the flat sides of the prop nut to keep it from backing off, use it
LI-SI-WI-NWI
|
|
Re: Prop Install
[Re: spankyttx]
#13350988
11/24/19 01:17 AM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
it's a lock, the tabs will bend up on the flat sides of the prop nut to keep it from backing off, use it Thx,I will have to loosen the nut a tad to get a flat side
|
|
Re: Prop Install
[Re: Bentman63]
#13351052
11/24/19 03:18 AM
|
Joined: Dec 2008
Posts: 16,188
grout-scout
TFF Guru
|
TFF Guru
Joined: Dec 2008
Posts: 16,188 |
Tighten it, if it’s so tight that you can’t spin the nut, then loosen. Depending on the prop, some use up to 100ft lb of torque, some are around 50ft lb.
Make sure you have those grooves in the spindle sleeve prongs.
|
|
Re: Prop Install
[Re: Bentman63]
#13351605
11/24/19 08:07 PM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
I went out and put it back on again. I made a video. I think it is good now. Video is crappy..but it works
|
|
Re: Prop Install
[Re: Bentman63]
#13351719
11/24/19 10:05 PM
|
Joined: Jan 2009
Posts: 1,649
spankyttx
Extreme Angler
|
Extreme Angler
Joined: Jan 2009
Posts: 1,649 |
i'm a little leery about that play you speak of but we can check it when you pick me up on the way to the berts (ray roberts)
LI-SI-WI-NWI
|
|
Re: Prop Install
[Re: Bentman63]
#13351795
11/24/19 10:56 PM
|
Joined: Dec 2008
Posts: 16,188
grout-scout
TFF Guru
|
TFF Guru
Joined: Dec 2008
Posts: 16,188 |
That play doesn’t seem too bad, but do check it after usage. But one thing I didn’t see you do, slap some grease on the prop shaft and all those washers.
If you were just using that box wrench, it’s prob not tight enough. But it doesn’t appear to be a large HP motor, so not sure if that’ll hurt anything or not, mines a bit different.
|
|
Re: Prop Install
[Re: spankyttx]
#13351806
11/24/19 11:06 PM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
i'm a little leery about that play you speak of but we can check it when you pick me up on the way to the berts (ray roberts) I will take you to ray roberts. whatcha wanna fish for? I usually try to catch crappie or catfish.. but I will fish for whatever I just have a 17 ft bass tacker pro..but it floats and so far has ran good
|
|
Re: Prop Install
[Re: Bentman63]
#13351835
11/24/19 11:24 PM
|
Joined: Jan 2009
Posts: 1,649
spankyttx
Extreme Angler
|
Extreme Angler
Joined: Jan 2009
Posts: 1,649 |
yes sir, crappie or catfish but prefer crappie
LI-SI-WI-NWI
|
|
Re: Prop Install
[Re: spankyttx]
#13351844
11/24/19 11:27 PM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
yes sir, crappie or catfish but prefer crappie me too..I can fish on weekends. lets see what the weather does and plan a trip I have never been to ray roberts..
|
|
Re: Prop Install
[Re: Bentman63]
#13351902
11/24/19 11:53 PM
|
Joined: Jan 2009
Posts: 1,649
spankyttx
Extreme Angler
|
Extreme Angler
Joined: Jan 2009
Posts: 1,649 |
....
LI-SI-WI-NWI
|
|
Re: Prop Install
[Re: Bentman63]
#13352461
11/25/19 01:41 PM
|
Joined: Aug 2006
Posts: 7,182
steve@S2Marine
TFF Celebrity
|
TFF Celebrity
Joined: Aug 2006
Posts: 7,182 |
Reflex hub kit's torque is typically around 50-55 ft lbs.
never loosen the prop nut to line up the lock tabs, over torque'ing slightly is okay.
|
|
Re: Prop Install
[Re: steve@S2Marine]
#13352695
11/25/19 05:56 PM
|
Joined: Sep 2019
Posts: 2,391
Bentman63
OP
Extreme Angler
|
OP
Extreme Angler
Joined: Sep 2019
Posts: 2,391 |
Reflex hub kit's torque is typically around 50-55 ft lbs.
never loosen the prop nut to line up the lock tabs, over torque'ing slightly is okay. It was as far as it would tighten. all I could do is loosen it just a tad. I may need to go get a torque wrench
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|