Hey y'all,
I fish Lake Buchanan mostly for Whites/Striper and similarly sized lakes. Will also fish bay fish in Galveston couple times a year. I've been looking for a used 1-3 year boats for around a month now and have always been looking at fiberglass. I just started looking into some aluminum boats such as the ranger 19RP or Alumacraft 18 SW Bay. What do you guys think is best for my needs? Will a fiberglass be much superior compared to a aluminum boat for my type of fishing?
Also, to make for sure, any boat with a carpet will get wrecked by saltwater correct? Are bass boats absolutely a no-no if I do plan to fish inshore? (Ranger Rt188)
Thanks!

Look into the War Eagle 961 Blackhawk.. I have one.. beats others hands down.. IMO.. I fish primarily fresh water but fished port aransas several times as well with it... Aluminum

I like fiberglass because the tend to be quieter and smoother running, but they take more HP so more expensive. Lots of great aluminum boats out there and are more popular at the coast all the time. I do like the center console as the best all around boat for fishing. As many before me have said, you never have a perfect boat. All boats have tradeoffs. Always hard to tell someone else what the best boat will be for their uses. Lake Buchanan fishing in the open water, I have a 19' and many times wish I had a 22'. It can get rough out there in a hurry. Yes if I never have another boat with carpet it will be too soon. Would never have taken my bass boat to the coast. To much electronics.
PS also don't go to the coast with a metal trailer, aluminum only in my opinion.
Good Luck

for whites and stripers I say fiberglass, especially if you are going to thump.

Fiberglass is also a very superior ride aluminum boats are light and will beat you up...lighter boat with fuel economy that can run with less horsepower etc. fiberglass imo

I have the perfect boat. LOL I got what i wanted and it is a beast. I have been out at tawakoni in 30 mph winds and this thing handles it and we stay dry... Just kidding i love my boat though :

I like fiberglass because it is easier to clean. I went with the big four stroke and don't use much gas and this boat is heavy. I haven't been to the coast yet but i am sure it will do fine. It's 22 foot 6 inches and almost 9 feet wide

Why is thumping better in fiberglass? I would figure that aluminum would be more conducive to thumping.

Much more..... Aluminum lasts forever...

I thump in my Lund all the time. If you are going to run a smaller boat, less than 20’ aluminum is cheaper, as they get bigger and the motor gets bigger the difference in price gets smaller. For smaller boats Aluminum boats require smaller motors and are not as fast. Flat bottom bass boats cannot handle wind/waves safely IMHO. I have a Lund deep V which manages better but it is definitely a tougher ride when it’s choppy as you don’t have the weight to cut through the waves.

I fish for sand bass and hybrids I mainly fish Richland Chambers and it can get choppy. My first boat was a fiber glass boat my next boat was an aluminum boat I have never regreated switching. As far as the ride it depends on the type of boat you get. With an aluminum boat it does not take much wind to blow you around where a fiber glass boat does not get pushed around so easily. My first aluminum boat was a deep vee boat my next and current boat is an Xpress H17 when the water gets to be pretty choppy instead of running wide open I idel back some so it does not beat me to death. Because aluminum boats are lighter they do not require a large engine, they can also be launched in shalower water. With my Xpress boat launching and trailering it is pretty easy. I would recommend that if you know of some one that has a fiber glass boat and some one else that has an aluminum boat go out with them and try them out to see which one you like as both boats have there pros and cons to them. Hope this helps you which boat you decide to get I am sure you will enjoy it.

I agree with everything above especially the idea of riding in different boats if you can. I went with fiberglass, my boat takes rough water really well, it’s a dry ride and I can get in and out quickly. I work 60-70 hours each week so I go fishing when I can and I can’t pick the weather or wind conditions. If you have a lot of time off or are retired it probably won’t make a difference. You can choose nice weather each trip. My boat will hold several people and all of our equipment.

I've got the same thoughts as the OP. I have a SeaArk 180XV SC and it thumps well, and is very stable but have really been looking at fiberglass CC for Buchanan and the coast. I've got it down to two that will fit in my garage... Blue Wave 1902 Evo or the NauticStar 1810. Both seem like great boats to me. I want fiber for the family as I have young kids and it just seems easier for them to deal with/cleaner. My dad has an Alumacraft CC and it is a very nice boat too.

I am not knocking Bluewave but when i was shopping for boats at the boat show the blue wave seemed to have too much flex in the fiberglass on the outer sides of the boat. Maybe they are different now. Also the blue wave 2200 pure bay was actually 21 foot 6 inches long. I went with 227 xts Nautic star it is 22 foot 6 inches and the fiberglass is solid all around. I looked at the Nauticstar 215 it is a really solid built boat . But i wanted bigger. Good luck

Thank you for that I will definitely keep the flex in mind when looking. Yeah I hate that the number doesn't match the length on the longer ones. It's sneaky.

I'm took a deal for an 2017 alumacraft MV 186 side console with 90 Yamaha for just 15000. How should I get it inspected? My first boat and I don't know anyone good with boats? Should I hire a mechanic? Thanks.