Forums59
Topics1,039,217
Posts13,961,125
Members144,196
|
Most Online39,925 Dec 30th, 2023
|
|
MotorGuide Tour Edition Prop Removal
#13156992
05/17/19 03:18 AM
|
Joined: Feb 2017
Posts: 390
lurenthewind
OP
Angler
|
OP
Angler
Joined: Feb 2017
Posts: 390 |
I can't get the prop off my MotorGuide Tour Edition trolling motor. The prop nut cam off with no problem, Bit I can't get the prop to budge.
I screwed the nut back on until it was flush and than struck the end of the shaft it with a hammer while putting pressure on the backside of the prop. I didn't hit it really hard for fear of damaging the armature. Didn't work
I tried prying on the back of the prop with a screwdriver between the prop and housing. Didn't work.
I tried hitting the backside of the prop blades alternately with a hammer. Didn't work
Any suggestions?
Wayne
Luck will beat skill any time you have enough of it!
|
|
Re: MotorGuide Tour Edition Prop Removal
[Re: lurenthewind]
#13157070
05/17/19 11:02 AM
|
Joined: Oct 2002
Posts: 6,102
ring fry
TFF Celebrity
|
TFF Celebrity
Joined: Oct 2002
Posts: 6,102 |
Sawsall.
SE Kansas grass grower
2008, 2022 NCAA Men's Basketball Champions GO JAYHAWKS
|
|
Re: MotorGuide Tour Edition Prop Removal
[Re: lurenthewind]
#13157169
05/17/19 01:01 PM
|
Joined: Jul 2007
Posts: 688
NITRO Z8
Pro Angler
|
Pro Angler
Joined: Jul 2007
Posts: 688 |
Spray some oil in there it's only being held on with a pin.
|
|
Re: MotorGuide Tour Edition Prop Removal
[Re: lurenthewind]
#13157314
05/17/19 02:53 PM
|
Joined: Feb 2017
Posts: 390
lurenthewind
OP
Angler
|
OP
Angler
Joined: Feb 2017
Posts: 390 |
I sprayed PB Blaster on it last night to let it soak. I will try again today and see how it goes.
I wanted to put a new prop on and keep this one for a spare, but I may have to cut it off.
Wayne
Luck will beat skill any time you have enough of it!
|
|
Re: MotorGuide Tour Edition Prop Removal
[Re: lurenthewind]
#13157359
05/17/19 03:46 PM
|
Joined: Nov 2010
Posts: 5,101
Wayne P.
TFF Celebrity
|
TFF Celebrity
Joined: Nov 2010
Posts: 5,101 |
Your shear pin must be bent preventing easy removal from the shaft.
Helix 12 CHIRP MEGA SI+ GPS G3N and G4N, 1198c SI, SOLIX 10 SI G3, Helix 8 MEGA SI+ GPS G4N, SOLIX 12 SI and G3, MEGA 360, MEGA LIVE TL, RC-1
|
|
Re: MotorGuide Tour Edition Prop Removal
[Re: lurenthewind]
#13157730
05/17/19 08:48 PM
|
Joined: Feb 2017
Posts: 390
lurenthewind
OP
Angler
|
OP
Angler
Joined: Feb 2017
Posts: 390 |
Well, I destroyed the prop getting it off. The shear pin was bent into and "L" and I even fashioned a puller out of a steering wheel puller that I have and had straps around all three of the prop blades and it would not budge. Finally just cut it off. I was going to put a new one on anyway, I was just trying to keep this one for a spare.
Wayne
Luck will beat skill any time you have enough of it!
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|