Forums59
Topics1,039,218
Posts13,961,132
Members144,196
|
Most Online39,925 Dec 30th, 2023
|
|
INLINE SPINNER QUESTION
#13109137
03/31/19 09:56 PM
|
Joined: Feb 2007
Posts: 6,699
JCBfromTHF
OP
TFF Celebrity
|
OP
TFF Celebrity
Joined: Feb 2007
Posts: 6,699 |
Not sure if anyone here builds their own spinners or not but figured I would ask anyway.
I cant find exactly what I am looking for so I am going to build my own. The part I am stuck on is the wire shaft size. The wire size I am looking for is the same size as what you get on the Blue Fox Vibrax 1/8oz #1blade.
Anyone know what size they use on that one?? If you don't know, then do you know what wire size would be the most commonly used on inlines in the 1/8-1/4oz size using #1 and #2 blades?
Thanks
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13109641
04/01/19 01:01 PM
|
Joined: Jan 2008
Posts: 19,797
Donald Harper
TFF Guru
|
TFF Guru
Joined: Jan 2008
Posts: 19,797 |
As custom bait builders we run into these same problems and questions all the time. It cost twice as much to custom build baits; because you cannot get those answers even from the manufacturer of the product that you are trying to replicate. My suggestion is; if you want to get it right without trial and error is to contact Blue Fox and make an attempt at answering your questions about the wire sizes. It is very doubtful that you will get to the right person.
If you order online, you will have some extra product sitting around waiting for an opportunity to use it because it is too large or too small for the application that you need it for. The good thing is Wire is cheap and can be purchased in small quantities at ACE Hardware. Take your Blue Fox into the store and match the wire as close as possible.
Each person you work with holds some promise to your future success. Websiite Sponsors: www.eletewater.com - Staying Hydrated www.lakeoviachic.com - Booking Mexico Trips 20 Hot Spot Mapping - GPS Contour Chips - Custom Spinner Baits - Jigs -Spooks Pure Extracts - Minnow-Night Crawler-Crayfish-Craylic
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13109783
04/01/19 03:06 PM
|
Joined: May 2003
Posts: 5,671
Slide_R
TFF Celebrity
|
TFF Celebrity
Joined: May 2003
Posts: 5,671 |
If you have one to measure against then use a pair of calipers to get you answer.
Robert Oleson aka Slide_R
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13110236
04/01/19 09:12 PM
|
Joined: Feb 2007
Posts: 6,699
JCBfromTHF
OP
TFF Celebrity
|
OP
TFF Celebrity
Joined: Feb 2007
Posts: 6,699 |
I have several but no calipers.
Based on some information I found about Mepps I pretty much have it narrowed down to either .024 or .026. Will probably just order both sizes.
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13121276
04/12/19 03:34 PM
|
Joined: Dec 2017
Posts: 228
cjbles
Outdoorsman
|
Outdoorsman
Joined: Dec 2017
Posts: 228 |
Try BumperStumpers. He has 100+ colors and sizes and will make them custom for you. www.bumperstumper.com. Talk to Kerry Kiker
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13316832
10/20/19 05:52 AM
|
Joined: Jan 2015
Posts: 390
Dakota22
Angler
|
Angler
Joined: Jan 2015
Posts: 390 |
Last edited by Dakota22; 10/20/19 05:53 AM.
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13321718
10/25/19 12:46 AM
|
Joined: Sep 2003
Posts: 780
SenkoSam
Pro Angler
|
Pro Angler
Joined: Sep 2003
Posts: 780 |
AFW (American Fishing Wire ) is the best I've used to make in-lines, Beetle Spins, weed guard added to jig heads and a spinnerbait that uses a bullet sinker, allowing a wide gap hook to be attached for my hand poured swimbaits.. Free s/h from Amazon: AFW Tooth Proof WireMany wire diameters, cheap, stainless steel wire and free s/h. I have 5 sizes starting with 30 ft. of 27# test for $4.81. and also 32, 38, 44 and 58# test for nearly the same amount. You'll never use it up but you will find many uses for it. Great quality wire !
Last edited by SenkoSam; 10/25/19 01:24 AM.
|
|
Re: INLINE SPINNER QUESTION
[Re: JCBfromTHF]
#13321953
10/25/19 11:42 AM
|
Joined: Apr 2019
Posts: 1,234
Jerry713
Extreme Angler
|
Extreme Angler
Joined: Apr 2019
Posts: 1,234 |
Not sure if anyone here builds their own spinners or not but figured I would ask anyway.
I cant find exactly what I am looking for so I am going to build my own. The part I am stuck on is the wire shaft size. The wire size I am looking for is the same size as what you get on the Blue Fox Vibrax 1/8oz #1blade.
Anyone know what size they use on that one?? If you don't know, then do you know what wire size would be the most commonly used on inlines in the 1/8-1/4oz size using #1 and #2 blades?
Thanks You might reach out to Malin wire. They sell stainless steel leader wire same as what SenkoSam posted just different brand. I've reached out to them with some in depth questions before and they were a big help. I addition to the leader wire I know they sell industrial wire too. https://malinco.com/
You get out of it what you put into it!
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|