Forums59
Topics1,037,820
Posts13,935,093
Members144,150
|
Most Online39,925 Dec 30th, 2023
|
|
Evinrude Intruder mechanic suggestions?
#12544815
12/20/17 02:57 PM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
I've got a 93 175 Intruder on a 94 Ranger 482vs. Motor seems to run great and has very good holeshot. Prop is a 23 Renegade and boat is running 59 mph gps, at 5300 rpm. I started with a 27 Shooter at 4700 rpm. I thought that dropping it 4 would increase the rpm's a little more than 600 rpm, so I'm concerned that there may be a fuel or spark issue.
The plugs look great and idle is good, with a little bit of spitting. Just had the regulator/rectifier replaced as well as the roller that controls the throttle and timing advance. I guess I just expected a little more top end higher rpm's. Dealer suggested just going lower on the prop pitch, but I want to be 100% sure the motor is right.
One person suggested replacing the optical sensor as he had a drop in rpm and replacing it fixed the problem. It's not an expensive part, so I might do that, but I'm thinking its a fuel issue as the plugs very light brown/gray. I replaced the steel reeds with Chris Carson reeds and that was a big improvement with idle and holeshot.
Any suggestions on a good mechanic in the DFW or within a couple of hours drive? Not wanting to just throw money at it, but want to make sure it's running properly.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12544935
12/20/17 04:22 PM
|
Joined: Jul 2010
Posts: 1,336
boatman025
Extreme Angler
|
Extreme Angler
Joined: Jul 2010
Posts: 1,336 |
We can check it out for you. we can do reeds, get all electric check out, you need to be turning at least 5500 ton 5700
Hughes Marine 3855 Osage Lane Wylie ,Texas
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12545335
12/20/17 09:09 PM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
Gary, I already changed the reeds and it was a big improvement. Im just tired of buying props, to try to get the rpms up, and want to make sure everything else is good. Im taking it out tomorrow to see if engaging the choke, while running WOT, helps. It has been suggested that I may have an air leak as it appears to be a little lean to me.
Ill get in touch with you after I try that.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12545398
12/20/17 10:16 PM
|
Joined: Jul 2010
Posts: 1,336
boatman025
Extreme Angler
|
Extreme Angler
Joined: Jul 2010
Posts: 1,336 |
VRO might not be giving enough fuel pressure
Hughes Marine 3855 Osage Lane Wylie ,Texas
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12545818
12/21/17 03:23 AM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
I was thinking that as well as a possible air leak at higher rpm. I read a post about a person with the same motor and similar symptoms. He had a float bowl leaking air. Changed out bowls and fixed the problem.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12553711
12/28/17 03:39 AM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
I took my boat out and tried hitting the choke while on plane. After a few seconds, the motor just started to bog down. Let off and it picked right back up. RPM's never got above 5200. Closer to 5100.Trimming the motor up until the boat got a little squirrely didn't make it rev higher.
I'm still really interested in some suggestions for an Evinrude outboard mechanic around DFW.
Nobody has any suggestions? Surely there's someone on here that has experience getting an older Intruder worked on.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12554215
12/28/17 03:39 PM
|
Joined: Jul 2010
Posts: 1,336
boatman025
Extreme Angler
|
Extreme Angler
Joined: Jul 2010
Posts: 1,336 |
I can look at it and check it out
Hughes Marine 3855 Osage Lane Wylie ,Texas
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12554339
12/28/17 05:21 PM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
Gary, I appreciate the offer, but I'm actually looking for peoples referral/opinions/experiences, more than a businesses offering to work on my engine.
So far I haven't had any luck getting that.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12554418
12/28/17 06:39 PM
|
Joined: Mar 2005
Posts: 756
Basshead21
Pro Angler
|
Pro Angler
Joined: Mar 2005
Posts: 756 |
Lake Park Marine in Valley View Tx.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12554424
12/28/17 06:46 PM
|
Joined: Jul 2010
Posts: 1,336
boatman025
Extreme Angler
|
Extreme Angler
Joined: Jul 2010
Posts: 1,336 |
we can still check it out for you
Hughes Marine 3855 Osage Lane Wylie ,Texas
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Basshead21]
#12554546
12/28/17 08:29 PM
|
Joined: Oct 2017
Posts: 122
Mgfan58
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Oct 2017
Posts: 122 |
Thanks. Ill give them a call.
|
|
Re: Evinrude Intruder mechanic suggestions?
[Re: Mgfan58]
#12554671
12/28/17 10:15 PM
|
Joined: Dec 2013
Posts: 459
PlanoPaul
Angler
|
Angler
Joined: Dec 2013
Posts: 459 |
Seems you always hear good things about Rockwall Marine, might give them a shot at it.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|