texasfishingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
TraeMartin, Power-Pole CS, T-Rigger, JoeGoes, EcKo
119150 Registered Users
Top Posters(All Time)
hopalong 120,571
TexDawg 119,516
Bigbob_FTW 94,879
John175☮ 85,892
Pilothawk 83,260
Bob Davis 81,480
Mark Perry 72,282
Derek 🐝 68,311
JDavis7873 67,416
Forum Statistics
Forums59
Topics1,037,820
Posts13,935,118
Members144,150
Most Online39,925
Dec 30th, 2023
Print Thread
Plugs for Raker II prop? #12450885 10/03/17 02:34 AM
Joined: Jun 2007
Posts: 468
ToadThrower Offline OP
Angler
OP Offline
Angler
Joined: Jun 2007
Posts: 468
Anyone know where I can find plugs for the holes in my Raker II prop...prop slips a little too much ...it has 3 holes in the hub about 5/8 inch each or suggestions on how to make plugs for them...appreciate any help...

Last edited by ToadThrower; 10/03/17 02:34 AM.
Re: Plugs for Raker II prop? [Re: ToadThrower] #12451312 10/03/17 02:42 PM
Joined: May 2003
Posts: 11,586
gary purdy Offline
TFF Guru
Offline
TFF Guru
Joined: May 2003
Posts: 11,586
JB Weld for metal.


The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
Re: Plugs for Raker II prop? [Re: ToadThrower] #12451342 10/03/17 02:56 PM
Joined: Jul 2007
Posts: 688
NITRO Z8 Offline
Pro Angler
Offline
Pro Angler
Joined: Jul 2007
Posts: 688
Try B&B prop's on rufe snow.

Re: Plugs for Raker II prop? [Re: NITRO Z8] #12451406 10/03/17 03:45 PM
Joined: Jun 2007
Posts: 468
ToadThrower Offline OP
Angler
OP Offline
Angler
Joined: Jun 2007
Posts: 468
Thanks for the suggestions...Gary on the JB weld any suggestions for how to fill that large hole..with the epoxy..I tried using JB weld with a grommet and it didn't hold..I will be visiting B and B so I will check with them too...

Re: Plugs for Raker II prop? [Re: ToadThrower] #12451783 10/03/17 07:29 PM
Joined: Aug 2006
Posts: 7,182
steve@S2Marine Offline
TFF Celebrity
Offline
TFF Celebrity
Joined: Aug 2006
Posts: 7,182
best is too get a shop to drill those hole out to accept the mercury pvs plugs.


www.hydrodynamics-usa.com
info@hydrodynamics-usa.com
903-763-5225
www.s2marine.com
s2marinesales@gmail.com
Blazer Boats, Gambler boats and Legend Craft Boats




Re: Plugs for Raker II prop? [Re: steve@S2Marine] #12451793 10/03/17 07:33 PM
Joined: Jun 2007
Posts: 468
ToadThrower Offline OP
Angler
OP Offline
Angler
Joined: Jun 2007
Posts: 468
Thanks Steve do you know what size hole diameter that would be?...I am sure the prop shop would know but I think the current hole size maybe too large for the PVS plugs...

Re: Plugs for Raker II prop? [Re: ToadThrower] #12451986 10/03/17 09:48 PM
Joined: May 2003
Posts: 11,586
gary purdy Offline
TFF Guru
Offline
TFF Guru
Joined: May 2003
Posts: 11,586
Anytime you are using JB weld to fill, I always wait until it gets like soft clay before applying. The holes for vent plugs on Merc props have a machined flat so it can retain the insert. Merc vent plugs fit into a .690 hole


The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
Re: Plugs for Raker II prop? [Re: gary purdy] #12453335 10/04/17 10:19 PM
Joined: Jun 2007
Posts: 468
ToadThrower Offline OP
Angler
OP Offline
Angler
Joined: Jun 2007
Posts: 468
Thanks for the tips and information Gary...

Previous Thread
Index
Next Thread

© 1998-2022 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3