Forums59
Topics1,037,829
Posts13,935,210
Members144,150
|
Most Online39,925 Dec 30th, 2023
|
|
Bent prop shaft
#12390967
08/18/17 03:28 PM
|
Joined: Sep 2003
Posts: 411
Jigman
OP
Angler
|
OP
Angler
Joined: Sep 2003
Posts: 411 |
Was washing my boat yesterday and noticed my prop was spinning out of line,can it be straightened.
Good Fishing.
|
|
Re: Bent prop shaft
[Re: Jigman]
#12392019
08/19/17 02:45 AM
|
Joined: Jun 2004
Posts: 1,509
OPTI
Extreme Angler
|
Extreme Angler
Joined: Jun 2004
Posts: 1,509 |
They can be has to be removed from case but I have never had one done they say it weakens the metal and will bend easier the next time or even break so I just recommend replacing it cause when I do it I have to warranty it...OPTI
|
|
Re: Bent prop shaft
[Re: Jigman]
#12394778
08/21/17 05:00 PM
|
Joined: Aug 2016
Posts: 1,476
T-racer @ Mallard Marine
Extreme Angler
|
Extreme Angler
Joined: Aug 2016
Posts: 1,476 |
Ronnie Fretwell at Xtreme Marine is able to do it. Of course if you can just get a new gear case under warranty or something like that then do it, but sometimes for those of us with no warranty that's not in the cards for the cost of a new gear case. If it isn't bent too bad, it shouldn't be something that just bends super easily again once it is fixed.
Last edited by T-racer; 08/21/17 05:01 PM.
Mallard Marine Nacogdoches, Tx 936-225-3244 - Authorized Sales/Service Mercury Outboards - Allison Boats
|
|
Re: Bent prop shaft
[Re: Jigman]
#12395001
08/21/17 07:16 PM
|
Joined: Oct 2016
Posts: 536
Bulletman99
Pro Angler
|
Pro Angler
Joined: Oct 2016
Posts: 536 |
First--If you have insurance and your policy covers "Under-Water Obstruction" turn in a claim. LU work is pretty expensive.
Second--I saw the video listed above a few years ago and caused quiet a stir on BBC. Having a mechanical background I can say with certainty I would never try that route. Bending a 1 inch solid hardened steel shaft housed inside bearings, an aluminum bearing carrier inside an aluminum housing is just asking for trouble!
Third---"DON'T" run it again until it's fixed. The wobble and load from the prop "WILL" cause additional problems.
Bullet 20XD Merc 250 ProXS
|
|
Re: Bent prop shaft
[Re: Jigman]
#12395116
08/21/17 08:33 PM
|
Joined: Jan 2003
Posts: 268
TSpencer
Angler
|
Angler
Joined: Jan 2003
Posts: 268 |
$170 at Nettles Props in Austin. They straighten on the engine without removing.
Had the same shaft straightened 3 times on my 2001 Yamaha 225 ox66. Fourth time I bent it so bad the boat would hardly plain. I decided to have it replaced this time. One of the best mechanics in the Austin area did the replacement. He said the bearings and carriers looked great. Just needed the shaft. That was 2 years ago...and still going strong with the original 2001 bearings and races.
BTW, Nettles has been doing this for years now. They've done hundreds from what I hear.
Last edited by TSpencer; 08/21/17 09:22 PM.
|
|
Re: Bent prop shaft
[Re: Jigman]
#12395689
08/22/17 02:49 AM
|
Joined: Nov 2002
Posts: 4,439
Gamblinman
TFF Team Angler
|
TFF Team Angler
Joined: Nov 2002
Posts: 4,439 |
Was washing my boat yesterday and noticed my prop was spinning out of line,can it be straightened. First, make sure it is your propshaft that is causing the issue. Pull the prop and lay something close to the shaft and spin it to check propshaft run out. Props can get installed incorrectly or bent.
|
|
Re: Bent prop shaft
[Re: Jigman]
#12400195
08/25/17 02:21 AM
|
Joined: Aug 2016
Posts: 1,476
T-racer @ Mallard Marine
Extreme Angler
|
Extreme Angler
Joined: Aug 2016
Posts: 1,476 |
Yeah checked on this for you and heard it straight from the horses mouth that they can be re straightened by the right guy, and that it is absolutely worth it. I couldn't explain it like he could but something about the degree of bend is so insignificant compared to the degree of bend needed to truly weaken the shaft.
Mallard Marine Nacogdoches, Tx 936-225-3244 - Authorized Sales/Service Mercury Outboards - Allison Boats
|
|
Re: Bent prop shaft
[Re: Jigman]
#12401047
08/25/17 06:45 PM
|
Joined: Sep 2003
Posts: 411
Jigman
OP
Angler
|
OP
Angler
Joined: Sep 2003
Posts: 411 |
Thanks for input, took it to Anglers Marine in seven points yesterday and Terry worked me in, called me 2 hours after drop off and ready.Have not ran it yet but it looks good,he said he got it to 4 thousands. nice guy
Good Fishing.
|
|
Re: Bent prop shaft
[Re: Jigman]
#12402059
08/26/17 02:44 PM
|
Joined: May 2003
Posts: 11,586
gary purdy
TFF Guru
|
TFF Guru
Joined: May 2003
Posts: 11,586 |
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
|
|
Re: Bent prop shaft
[Re: Jigman]
#12411632
09/02/17 10:00 PM
|
Joined: Mar 2010
Posts: 218
way2slow on h2o
Outdoorsman
|
Outdoorsman
Joined: Mar 2010
Posts: 218 |
Bent Propshaft Straightening:
This is an ongoing debate, and I can assure you, it can be done. I've been racing boats since '82 and have bent more shafts than I can count. Being neighbors with a Metallurgist at Lockheed and having access to both a Brinell and Rockwell hardness testers, I was able to determine this about prop shafts:
A: the shaft is not hardened (if so, how does a rubber seal wear a groove in the shaft?) B: the small amount the shaft bends does not change the molecular structure around the affected area. C: straightening does not "weaken" the metal
We've straightened literally hundreds of shafts to 0.000-0.002" (factory spec is 0.003") without ramifications. I can spin my race prop 5730 rpm (10,200 rpm on motor) so on a stock fishing gear case @ 6000 rpm the Propshaft is spinning a mere 3200 r's....
|
|
Re: Bent prop shaft
[Re: Jigman]
#12419204
09/08/17 05:22 PM
|
Joined: Jun 2008
Posts: 3,334
Hog Jaw
TFF Team Angler
|
TFF Team Angler
Joined: Jun 2008
Posts: 3,334 |
Not know smarty but when you hammer down on the throttle a little torque is made which may "bend " the shaft ???
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|