texasfishingforum.com logo
Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
TraeMartin, Power-Pole CS, T-Rigger, JoeGoes, EcKo
119150 Registered Users
Top Posters(All Time)
hopalong 120,579
TexDawg 119,518
Bigbob_FTW 94,889
Pilothawk 83,260
Bob Davis 81,483
Mark Perry 72,289
JDavis7873ฎ 67,416
Forum Statistics
Forums59
Topics1,037,836
Posts13,935,340
Members144,150
Most Online39,925
Dec 30th, 2023
Print Thread
96 mercury 200 efi #12754340 05/14/18 01:31 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
How can I check to make sure my fire to plugs is strong enough? I am still having problems with motor bogging down when I first take off. I have deleted oiler and only premix my gas.

Thanks,

Re: 96 mercury 200 efi [Re: CWSANDERS] #12755263 05/14/18 09:42 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
tpi been checked/set?.. injectors cleaned lately? clean filters (especially tha one on tha bottom of tha fuel pump)?.. idle and max timing been checked.. jus some of tha "little" things.... ya need a test board for tha plugs if ya not sure as to what ya lookin' at....

Last edited by TLW; 05/14/18 09:44 PM.
Re: 96 mercury 200 efi [Re: CWSANDERS] #12755901 05/15/18 11:15 AM
Joined: May 2003
Posts: 11,586
gary purdy Offline
TFF Guru
Offline
TFF Guru
Joined: May 2003
Posts: 11,586
Like TLW said many things can cause the bogging but some easy things you can check: grey fuel line from bulb to motor( enter liner of hose collapses restricting fuel) thermostats, one may be stuck open or could have been removed (motor needs to reach correct operating temp) check compression (weak or bad cylinder will affect performance) Check each cylinder for spark and check each cylinder for combustion by pulling each plug wire, one at a time while running. You can connect a remote fuel tank to see if your problem is fuel related. Let us know what you find.


The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
Re: 96 mercury 200 efi [Re: CWSANDERS] #12755931 05/15/18 12:10 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
I will look into these things. I know that injectors have not been serviced. Is there a local place I can take them?

Re: 96 mercury 200 efi [Re: CWSANDERS] #12756240 05/15/18 03:47 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
do you have an oem manual? if not send me an email addy so I can send ya one in pdf.....

Last edited by TLW; 05/15/18 03:48 PM.
Re: 96 mercury 200 efi [Re: CWSANDERS] #12756279 05/15/18 04:21 PM
Joined: Sep 2011
Posts: 1,751
P
Peepaw on Fork Offline
Extreme Angler
Offline
Extreme Angler
P
Joined: Sep 2011
Posts: 1,751
Run some Mercury Quickleen through it.


H. Burns
Re: 96 mercury 200 efi [Re: CWSANDERS] #12756398 05/15/18 05:47 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
TLW thanks. You have already sent it to me awhile back.

Re: 96 mercury 200 efi [Re: CWSANDERS] #12756663 05/15/18 09:13 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
I saw that lookin' back this afternoon.. had any luck trackin' it down?

Re: 96 mercury 200 efi [Re: CWSANDERS] #12756676 05/15/18 09:20 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
I have not been able to look at it yet hopefully this weekend. Been busy. I am going to check compression and fire first. Would I be best just to start it then start pulling plug wire one at a time to see if there is a difference with motor running. I have a single plug tester but don’t know how well that work with figuring out a problem. I also have a compression tester so I can for sure do that.

Re: 96 mercury 200 efi [Re: CWSANDERS] #12756697 05/15/18 09:31 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
if it runs ok at idle and wot (once past tha bog) it may be hard ta tell just pullin' a wire at a time.. think low comp and/or bad 'lectrics will show at justa 'bout all ranges. they usually work or don't work,.. jmo. but fuel delivery can act different at any given range, 'specially with efi stuff.. again, jmo.

there is one 'lectric part if you still have it on tha motor.. idle/timing stabilizer.. if so, chunck it.

Last edited by TLW; 05/15/18 09:40 PM.
Re: 96 mercury 200 efi [Re: CWSANDERS] #12759265 05/17/18 06:32 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
Ok so was looking at the motor before work this morning. I have 2 modules left on motor. I have take the one off for the Oiler already. The is one left on the top of head on port side and one on the side of the motor on port side. Should both of these be removed?

Re: 96 mercury 200 efi [Re: CWSANDERS] #12759568 05/17/18 10:10 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
(idle/timin' stab.) has white/black, red/white, black?.. (detonation control) has three white/blacks two of which have insulated eyelets and one a bullet end, one white/blue with detonation connector, one purple, one green, one gray/white, one black?


Last edited by TLW; 05/17/18 10:13 PM.
Re: 96 mercury 200 efi [Re: CWSANDERS] #12763962 05/21/18 07:35 PM
Joined: Jan 2005
Posts: 369
C
CWSANDERS Offline OP
Angler
OP Offline
Angler
C
Joined: Jan 2005
Posts: 369
Does both these need to be removed or just idle control

Re: 96 mercury 200 efi [Re: CWSANDERS] #12764008 05/21/18 08:11 PM
Joined: Nov 2006
Posts: 2,846
T
TLW Offline
Extreme Angler
Offline
Extreme Angler
T
Joined: Nov 2006
Posts: 2,846
I always did.. tha stabilizer white/black should have a joint made somewhere in tha sleeve that splits it up going to tha switch boxes.. you can eliminate it with tha module but you will need to make a short white/black "jumper" to go between tha two switch boxes to replace it..

tha det module has a gray/white that plugs into a gray/white from tha harness.. if you remove it you will need to "ground" tha harness gray/white.. anywhere on tha motor is fine...

Previous Thread
Index
Next Thread

© 1998-2022 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide
Powered by UBB.threads™ PHP Forum Software 7.7.3