Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
ET8300, NWRoadstriper, MOTEXAN, SaltyFishermom, AHSbassser
108240 Registered Users
Top Posters
TexDawg 88897
hopalong 78895
Pilothawk 76460
John175® 67856
JDavis7873® 67390
FattyMcButterpants 60885
Derek 🐝 60484
Tritonman 58050
LoneStarSon® 54521
SkeeterRonnie 53418
facebook
Forum Stats
108240 Members
60 Forums
863930 Topics
12307372 Posts

Max Online: 36273 @ 01/23/13 02:34 PM
Topic Options
#12622633 - 02/11/18 07:10 PM Removing a puck epoxied in the hull
Stump jumper Online   content
TFF Celebrity

Registered: 04/19/04
Posts: 7974
Loc: Rockwall
I think I screwed up when I mounted the puck in the hull. Pretty certain that thinking about my boat has balsa core or floatation in the keel. Working in 40 degree weather and nasty wind will cause you to not think logically. I am going to test before removing. I have heard that a block of wood and a good rap with a hammer should do the job. Fortunately I have plenty of room to work on it.
_________________________
2200 Bay Champ/200 Mercury Optimax
2017 Tundra TSS 4x4 Crewmax 5.7L

Top
#12622781 - 02/11/18 08:15 PM Re: Removing a puck epoxied in the hull [Re: Stump jumper]
javelin150 Online   content
Pro Angler

Registered: 03/19/06
Posts: 947
Loc: Waco, TX
Yep, block of wood and a good whack will do the trick

Top
#12623112 - 02/12/18 05:58 AM Re: Removing a puck epoxied in the hull [Re: Stump jumper]
Dayne Online   content
TFF Team Angler

Registered: 12/16/06
Posts: 3058
You will need to grind the old epoxy off before you install a new xducer.

Top
#12623785 - 02/12/18 12:08 PM Re: Removing a puck epoxied in the hull [Re: Dayne]
Stump jumper Online   content
TFF Celebrity

Registered: 04/19/04
Posts: 7974
Loc: Rockwall
Originally Posted By: Dayne
You will need to grind the old epoxy off before you install a new xducer.
Not installing a new one in the same spot. Transducer is fine location is not. Just made a bad decision while working in the cold on Saturday. That and the fact that it took me a while to figure out that the wire conduit in the back of the boat was not continuous up to the console. By the time I got the wire run I just wanted out of the cold.
_________________________
2200 Bay Champ/200 Mercury Optimax
2017 Tundra TSS 4x4 Crewmax 5.7L

Top
#12633512 - 02/17/18 08:30 PM Re: Removing a puck epoxied in the hull [Re: Stump jumper]
blackhorse Offline
Outdoorsman

Registered: 05/13/08
Posts: 189
Loc: Morgan, Tx
dremel works great

Top
#12633821 - 02/18/18 08:52 AM Re: Removing a puck epoxied in the hull [Re: Stump jumper]
Capt Craig Offline
Extreme Angler

Registered: 08/25/09
Posts: 1602
Loc: Richland-Chambers
Transducers in the hull never provide good readings.
_________________________
Capt. Craig Copeland
Licensed by the US Coast Guard

2013 Nautic Star 2110 Shallow Bay Boat
Humminbird HELIX 12 CHIRP MEGA SI GPS G2N
Nautic Star Boats Pro Staff (nauticstarboats.com)
Redneck Fish'n Jigs Pro Staff (redneckfishn.com)

Top
#12638722 - 02/21/18 05:36 AM Re: Removing a puck epoxied in the hull [Re: Capt Craig]
HappyNest Offline
Outdoorsman

Registered: 06/30/16
Posts: 70
Loc: Texas
I agree with the block of wood and a hammer. It sounds violent and I was cautious but it worked. The epoxy separates at the fiberglass floor. The only issue I had was space to work in that area.

Top



© 1998-2018 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide