|
Forums59
Topics1,038,938
Posts13,955,886
Members144,183
| |
Most Online39,925
Dec 30th, 2023
|
|
 Trolling motor making grinding noise.
#12287451
06/10/17 02:33 PM
|
Joined: Dec 2013
Posts: 302
E-bright
OP
Angler
|
|
OP
Angler
Joined: Dec 2013
Posts: 302 |
Hit a rock with a minn kota crusing pretty fast. I took the shear pin off but now im having trouble getting the back and front lined up to get it back together. Did i pull it out to far?
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287455
06/10/17 02:35 PM
|
Joined: Nov 2007
Posts: 5,515
ssmith
TFF Celebrity
|
|
TFF Celebrity
Joined: Nov 2007
Posts: 5,515 |
probly bent the upper shaft
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287467
06/10/17 02:45 PM
|
Joined: Jan 2008
Posts: 19,792
Donald Harper
TFF Guru
|
|
TFF Guru
Joined: Jan 2008
Posts: 19,792 |
Time to go to:
Boris Marine for repair:
817-624-3932
5310 Azle Ave.
Fort Worth
Each person you work with holds some promise to your future success. Websiite Sponsors: www.eletewater.com - Staying Hydrated www.lakeoviachic.com - Booking Mexico Trips 20 Hot Spot Mapping - GPS Contour Chips - Custom Spinner Baits - Jigs -Spooks Pure Extracts - Minnow-Night Crawler-Crayfish-Craylic
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287507
06/10/17 03:28 PM
|
Joined: Jul 2003
Posts: 604
fisherman dan
Pro Angler
|
|
Pro Angler
Joined: Jul 2003
Posts: 604 |
I have a spare TM minnkota 55lb, long shaft. PM me if you think you could use some parts off it.
Tight Lines!
God Bless
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287620
06/10/17 05:37 PM
|
Joined: Dec 2003
Posts: 3,485
meP2too
TFF Team Angler
|
|
TFF Team Angler
Joined: Dec 2003
Posts: 3,485 |
you could have chipped one of the magnets inside the housing.
they cost about 60 bucks
take off the prop, undo the two screws on the back plate, pull the winding / armatures out there is some resistence from the magnets. see if any metal / magnet chips come out. if your careful you might be able to re-use your seals, but if you think the screw threds damaged the rubber put in a new gasket pack. about 25 bucks.
if magnet chips come out, clean them out thoroughly, you can put it back together and run it with cracked magnets, there will be some loss of power, order a new housing with magnets and then disassemble and reassemble when the housing arrives, this time get a gasket pack and new armatures.
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287622
06/10/17 05:39 PM
|
Joined: Jul 2003
Posts: 594
BassnRoun
Pro Angler
|
|
Pro Angler
Joined: Jul 2003
Posts: 594 |
I recently had the same problem. Mechanic disassembled the
Motor and the magnet had broken. I have a 70
Lb thrust Minnkota 24V model. Called Minnkota and
Ordered the middle section which encapsulates the
Large magnet. Surprisingly, it was only about
$45! Also order the gaskets. Running like new.
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287625
06/10/17 05:44 PM
|
Joined: Dec 2003
Posts: 3,485
meP2too
TFF Team Angler
|
|
TFF Team Angler
Joined: Dec 2003
Posts: 3,485 |
Hit a rock with a minn kota crusing pretty fast. I took the shear pin off but now im having trouble getting the back and front lined up to get it back together. Did i pull it out to far? you may not be spreading the brushes to allow bearing and upper armature to pass by.
|
|
|
Re: Trolling motor making grinding noise.
[Re: E-bright]
#12287892
06/10/17 11:00 PM
|
Joined: Dec 2013
Posts: 302
E-bright
OP
Angler
|
|
OP
Angler
Joined: Dec 2013
Posts: 302 |
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|
