Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
Mason777, RealCamSmith, Ol' Swamp Badd, Redneckcrappiedude, Djbfishing
103981 Registered Users
Top Posters
TexDawg 84217
hopalong 75953
Pilothawk 74193
JDavis7873® 67380
John175 ® 62192
FattyMcButterpants 60645
Tritonman 57318
Derek 57172
SkeeterRonnie 52704
LoneStarSon® 52587
facebook
Forum Stats
103981 Members
61 Forums
833069 Topics
11901481 Posts

Max Online: 36273 @ 01/23/13 02:34 PM
Topic Options
#11917016 - 11/04/16 01:40 PM HDSI Location
hocdrummer Offline
Outdoorsman

Registered: 01/29/16
Posts: 121
Loc: Fort Worth, TX
I mounted an HDSI transducer on my transom. Its about 1/4 inch below the bottom of the boat. Im losing bottom at speed on 2D and getting a roster tail. Where would you start? Move the ducer down or up?

Top
#11917031 - 11/04/16 01:51 PM Re: HDSI Location [Re: hocdrummer]
Wayne P. Online   content
TFF Team Angler

Registered: 11/16/10
Posts: 3564
Loc: Charlottesville, Va
The temp sensor end needs to be lower than the leading end to get water flow across its face.

Anytime you put an obstruction in water at speed, you will get a rooster tail---simple physics.
_________________________
Humminbird Helix 12 CHIRP SI, 1198c SI, 1198c SI, ONIX 10 SI NT, Helix 7 CHIRP SI GPS G2, SOLIX 12 SI, 360, RC-1

Top
#11917185 - 11/04/16 03:28 PM Re: HDSI Location [Re: hocdrummer]
hocdrummer Offline
Outdoorsman

Registered: 01/29/16
Posts: 121
Loc: Fort Worth, TX
Ive got the back of the ducer (the closer part to the transom) a few clicks down so it angles up a bit. Is that what you are referring to?

If you lose the bottom at speed where would you start moving the ducer?

Top
#11917322 - 11/04/16 04:57 PM Re: HDSI Location [Re: hocdrummer]
Txduckhunter Online   content
Extreme Angler

Registered: 02/19/02
Posts: 1455
Loc: Lake Fork
I'd buy a thru-hull for 2d and run it when I was on pad.

Top
#11917335 - 11/04/16 05:20 PM Re: HDSI Location [Re: hocdrummer]
44 Diesel Online   content
TFF Team Angler

Registered: 12/25/12
Posts: 4048
Loc: Burleson,TX
Might want to consider a 2d user along with the hdsi transducer with a y cable. If you went with the shoot thru ducer you would have to go with the alumaducer to shoot through aluminum

Top
#11917360 - 11/04/16 05:46 PM Re: HDSI Location [Re: hocdrummer]
Wayne P. Online   content
TFF Team Angler

Registered: 11/16/10
Posts: 3564
Loc: Charlottesville, Va
Originally Posted By: hocdrummer
Ive got the back of the ducer (the closer part to the transom) a few clicks down so it angles up a bit. Is that what you are referring to?

If you lose the bottom at speed where would you start moving the ducer?


Did you read the Installation Guide for that transducer?

It is here, download the guide and refer to section 5:

http://www.humminbird.com/Products/XHS-9-HDSI-180-T/

If you have a stepped transom, you have go by the bottom of the hull, not the bottom of the transom that the motor is attached to.


Edited by Wayne P. (11/04/16 05:48 PM)
_________________________
Humminbird Helix 12 CHIRP SI, 1198c SI, 1198c SI, ONIX 10 SI NT, Helix 7 CHIRP SI GPS G2, SOLIX 12 SI, 360, RC-1

Top
#11918141 - 11/05/16 09:34 AM Re: HDSI Location [Re: hocdrummer]
hocdrummer Offline
Outdoorsman

Registered: 01/29/16
Posts: 121
Loc: Fort Worth, TX
Got it. Ill adjust the angle and re test. Thanks!

Top
#11921057 - 11/07/16 09:49 AM Re: HDSI Location [Re: hocdrummer]
Jones Trolling Motor Offline
Angler

Registered: 05/01/11
Posts: 457
Loc: NE Texas/SW Arkansas
which boat do you have?
_________________________

www.jonestrollingmotor.com
texarkana, Ark/Tx

Top



© 1998-2017 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide