|
Forums59
Topics1,038,949
Posts13,956,276
Members144,183
| |
Most Online39,925
Dec 30th, 2023
|
|
 Ranger: Compartment Lid detached from Hinge????
#11896734
10/24/16 02:41 PM
|
Joined: Dec 2012
Posts: 25
Tire Master
OP
Outdoorsman
|
|
OP
Outdoorsman
Joined: Dec 2012
Posts: 25 |
So this is a new one....seems it's always something! My son raised the lid on the main deck storage compartment on my 2003 520VX...and the lid pulled apart from the hinges!!! UGH! I figured they used screws to attached the hinges to the lid but I noticed they used some sort of rivet??? Before I tackle this one...has anyone else had to do this? If so...HOW??? 
|
|
|
Re: Ranger: Compartment Lid detached from Hinge????
[Re: Tire Master]
#11897161
10/24/16 06:18 PM
|
Joined: May 2003
Posts: 11,586
gary purdy
TFF Guru
|
|
TFF Guru
Joined: May 2003
Posts: 11,586 |
You have to remove screws holding the hinge, re-pop rivet it to the hinge, then re-install.
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
|
|
|
Re: Ranger: Compartment Lid detached from Hinge????
[Re: Tire Master]
#11897489
10/24/16 08:41 PM
|
Joined: Aug 2011
Posts: 2,957
Bob Landry
Extreme Angler
|
|
Extreme Angler
Joined: Aug 2011
Posts: 2,957 |
I would also use a thin washer for a backer for the rivet to keep it from digging into fiberglass.
2015 Seaark 1872 MV CC Etec-90
Two Helix 12 CHIRP SI's, , MinnKota Riptide ST80/i-pilot Link, Bob's Hydraulic
2020 Robalo R200 CC, Yamaha 150
Bitter Gun Owner
Bitter Clinger
Armed Infidel
|
|
|
Re: Ranger: Compartment Lid detached from Hinge????
[Re: Tire Master]
#11897983
10/25/16 01:30 AM
|
Joined: Jun 2011
Posts: 2,235
Jimfishes
Extreme Angler
|
|
Extreme Angler
Joined: Jun 2011
Posts: 2,235 |
Use a drill and drill out each rivet....then use bolts, washers, and nuts to attach lid and tighten up snug.
|
|
|
Re: Ranger: Compartment Lid detached from Hinge????
[Re: Jimfishes]
#11901063
10/26/16 06:07 PM
|
Joined: Apr 2004
Posts: 14,069
Stump jumper
TFF Guru
|
|
TFF Guru
Joined: Apr 2004
Posts: 14,069 |
Use a drill and drill out each rivet....then use bolts, washers, and nuts to attach lid and tighten up snug. bolts or a longer rivet with a washer. I did the latter
2200 Bay Champ/200 Mercury Optimax
2017 Tundra TSS 4x4 Crewmax 5.7L
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|
