Forums59
Topics1,037,834
Posts13,935,305
Members144,150
|
Most Online39,925 Dec 30th, 2023
|
|
26 Fury, 250 Pro XS and 206 Champion
#11652583
06/07/16 07:58 PM
|
Joined: Jan 2009
Posts: 951
Hunter's Dad
OP
Pro Angler
|
OP
Pro Angler
Joined: Jan 2009
Posts: 951 |
I'm only getting about 5400 RPM. If I raise it up should I gain a little? With a heavy load I am not jumping on plane. Will raising the motor make this even worse? 26 pitch Fury 3 blade on 250 pro XS on a champion 206 with 6 inch manual jack plate.
I'm at the lake and can try a few things.
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11652774
06/07/16 09:23 PM
|
Joined: Sep 2003
Posts: 5,511
Bruce's
TFF Celebrity
|
TFF Celebrity
Joined: Sep 2003
Posts: 5,511 |
Raise it about a 1/8 at a time. Wish i had know you were there i am doing the same thing with my 202 and 250 pro xs
Bruce's Sprinkler Repair 817-798-7246 52 years experience State Licensed Irrigation LI0017483
Fishing Texas lakes one at a time
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11652783
06/07/16 09:27 PM
|
Joined: Sep 2003
Posts: 5,511
Bruce's
TFF Celebrity
|
TFF Celebrity
Joined: Sep 2003
Posts: 5,511 |
Right now i am having a problem my self. i am running up to around 4850 and getting chin walk so bad i cant run it anymore. I have had it up to 5100 and thought i was going to roll over. 27 pitch worked tempest. Throwing a tail about 2 foot tall and 30 yards long, but the transom comes to far out of the water.
Bruce's Sprinkler Repair 817-798-7246 52 years experience State Licensed Irrigation LI0017483
Fishing Texas lakes one at a time
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653426
06/08/16 02:11 AM
|
Joined: Jan 2009
Posts: 951
Hunter's Dad
OP
Pro Angler
|
OP
Pro Angler
Joined: Jan 2009
Posts: 951 |
Raised it 1/4 inch and gained 1000 RPM. Going to raise it a little more tomorrow. What water pressure should I expect and at what point should I get worried?
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653770
06/08/16 09:52 AM
|
Joined: Sep 2008
Posts: 120,579
hopalong
Pescador Loco
|
Pescador Loco
Joined: Sep 2008
Posts: 120,579 |
raise it till water pressure drops some, then lower 1/4". that should be your optimum.
" Hop, set the hook"! hopalong 99,999 TexDawg 99,999 FJB! not my president by a long shot!
lake fork FISHERMANS COVE MARINA/reservations - 903 474 7479
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653809
06/08/16 11:30 AM
|
Joined: Dec 2003
Posts: 35,817
Allison1
TFF Guru
|
TFF Guru
Joined: Dec 2003
Posts: 35,817 |
A 26 may be a little too much prop for that boat.
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653864
06/08/16 12:21 PM
|
Joined: Feb 2007
Posts: 702
Rick Collis
Pro Angler
|
Pro Angler
Joined: Feb 2007
Posts: 702 |
25 Fury might be a better option. Holeshot and performance will get worse as the air and water warm up. I run a 25 Fury with extra vent holes on my 250 and not completely thrilled with the holeshot when loaded. I am considering a Bravo 1XS. Good luck
Rick Collis 903-473-8820
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653967
06/08/16 01:26 PM
|
Joined: Jan 2005
Posts: 16,638
Pat Goff
TFF Guru
|
TFF Guru
Joined: Jan 2005
Posts: 16,638 |
Fury is not my first choice on a 206. Get with Steve and find a tempest he's worked, THAT will deliver your best results.
Pat Goff Seadrift TX
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11653972
06/08/16 01:28 PM
|
Joined: Jan 2013
Posts: 2,104
reelswift
Extreme Angler
|
Extreme Angler
Joined: Jan 2013
Posts: 2,104 |
I agree try a 25 pitch prop. Hole shoot will improve and RPM will increase.
Team LVS34 Captain WNB
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11654306
06/08/16 03:54 PM
|
Joined: Aug 2006
Posts: 7,182
steve@S2Marine
TFF Celebrity
|
TFF Celebrity
Joined: Aug 2006
Posts: 7,182 |
on the 206 and 210 i prefer a 10 or 12 inch setback.
then set the prop shaft height at 3" below and let er rip!!!
the 6" plate isn't giving you the bow lift you need to un wet the hull. thats why the rpms are low
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11654830
06/08/16 06:40 PM
|
Joined: Jan 2009
Posts: 951
Hunter's Dad
OP
Pro Angler
|
OP
Pro Angler
Joined: Jan 2009
Posts: 951 |
I raised it up just a bit more and didn't gain anything. Still 5500 RPM. Did lift a little better. I have a 25 Tempest that I can try if I get the hub changed. I had it on a 200 EFI. Water pressure is 17-18 Psi right now.
|
|
Re: 26 Fury, 250 Pro XS and 206 Champion
[Re: Hunter's Dad]
#11656171
06/09/16 03:50 AM
|
Joined: Apr 2010
Posts: 223
wkh2006
Outdoorsman
|
Outdoorsman
Joined: Apr 2010
Posts: 223 |
I'm running a 2008 210 champion with a 25 fury. Propshaft is 2" below pad running 73mph gps at 6k rpm and 25 psi water pressure at wot. This boat hated the tempest plus for some reason. Motor is a 250 pro xs by the way. And 10" slidemaster jackplate.
Last edited by wkh2006; 06/09/16 03:52 AM.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|