Forums59
Topics1,037,879
Posts13,935,963
Members144,150
|
Most Online39,925 Dec 30th, 2023
|
|
lowrance gen3 update problems
#11504324
03/27/16 07:42 PM
|
Joined: Jul 2015
Posts: 258
tin man 55
OP
Angler
|
OP
Angler
Joined: Jul 2015
Posts: 258 |
so, I updated by gen3-7 and gen3-9 units yesterday with the 3.0 update from micro sd card. everything seemed to work OK, but now I have problems with both units (they are linked together).
the gen3-7 at the cockpit acts like it is turning on when I hit the power button, the screen lights up with the startup, but then it just goes blank; can't tell if it's on or off.
the gen3-9 unit on the bow works on sonar, but the temp is reading "---" and it will not use the navionics chip in the other unit.
I think there is a hard reset to factory specs (something involving the power button and the pages button); will this undo the update that I installed?
also, I see that there is a new update (version 3.5); should I just install it and see if that fixes the issues?
I plan to call Lowrance customer service tomorrow, but thought maybe some forum members have experienced this and know what to do.
2014 Ranger RT-188 115 Mercury Pro-XS Lowrance Gen-3 units Ultrex
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11504350
03/27/16 08:05 PM
|
Joined: Nov 2015
Posts: 95
wallyandre
Outdoorsman
|
Outdoorsman
Joined: Nov 2015
Posts: 95 |
Install the 3.5 before doing anything else. Also unplug the ethernet cable when you do you're update.
Last edited by wallyandre; 03/27/16 08:06 PM.
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11504784
03/28/16 12:56 AM
|
Joined: Jul 2015
Posts: 258
tin man 55
OP
Angler
|
OP
Angler
Joined: Jul 2015
Posts: 258 |
thanks wallyandre. I just downloaded 3.5 update and copied over to my micro sd card. i'll give it a try tomorrow and see what happens.
2014 Ranger RT-188 115 Mercury Pro-XS Lowrance Gen-3 units Ultrex
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11504799
03/28/16 12:59 AM
|
Joined: Jun 2005
Posts: 1,014
jfdawson
Extreme Angler
|
Extreme Angler
Joined: Jun 2005
Posts: 1,014 |
Also, remove your Navionics card when doing the install.
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11507908
03/29/16 12:33 PM
|
Joined: Jul 2015
Posts: 258
tin man 55
OP
Angler
|
OP
Angler
Joined: Jul 2015
Posts: 258 |
update....
I disconnected the Ethernet cable and removed all micro sd cards, inserted the card with the 3.5 update into the HDS3-7 and turned it on. the update loaded normally and I have my screen back. did the same to my HDS3-9 and it worked fine too.
still have a problem though. the temperature is still not showing. if I "restore defaults", it works; but of course this removes all my settings. if I power down the unit, when I power on again, the temp is gone again.
I hooked the Ethernet cable back up and inserted the navionics card, and I can switch back and forth between the navionics and the insight map. I can also switch between transducers with no problem.
i'll be on the phone with lowrance about this today. I spoke to a couple of guys at the storage facility where I keep my boat and they said they had never updated their units because they heard about these kind of problems.
anyone have any idea about how to restore the software back to the original?
2014 Ranger RT-188 115 Mercury Pro-XS Lowrance Gen-3 units Ultrex
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11507932
03/29/16 12:41 PM
|
Joined: Jun 2005
Posts: 1,014
jfdawson
Extreme Angler
|
Extreme Angler
Joined: Jun 2005
Posts: 1,014 |
I'll bet if you read the manual on "edit overlay" and understand how to assign "data sources" you can get the temp back on any screen you want. Sometimes doing a software update or even a Hard reset you will lose all of your preset settings.
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11508472
03/29/16 03:46 PM
|
Joined: Jul 2015
Posts: 258
tin man 55
OP
Angler
|
OP
Angler
Joined: Jul 2015
Posts: 258 |
the "water temp" title is on the screen, but shows "- - -" in place of an actual temperature number.
I have the manual so i'll read about edit overlay, but since the field is on the screen, shouldn't it show the value?
2014 Ranger RT-188 115 Mercury Pro-XS Lowrance Gen-3 units Ultrex
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11508653
03/29/16 04:57 PM
|
Joined: Jun 2005
Posts: 1,014
jfdawson
Extreme Angler
|
Extreme Angler
Joined: Jun 2005
Posts: 1,014 |
is your Sonar Transducer in the bilge area or mounted to the transom?
PM me your phone # and I'll walk you though some instructions.
Jeff
|
|
Re: lowrance gen3 update problems
[Re: tin man 55]
#11508657
03/29/16 04:59 PM
|
Joined: Jun 2005
Posts: 1,014
jfdawson
Extreme Angler
|
Extreme Angler
Joined: Jun 2005
Posts: 1,014 |
here's where to check: Go to Settings/ Networking/ DATA SOURCEs. then Click on SONAR, and them click WATER TEMP; look at where the check mark is ?
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|