Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
Reed Cullum, BCBJIGMO82, Wulfgang Milez, westtexas920, JS2
106138 Registered Users
Top Posters
TexDawg 86627
hopalong 78748
Pilothawk 75356
JDavis7873® 67383
John175 ® 65451
FattyMcButterpants 60793
Derek 🐝 58685
Tritonman 57666
LoneStarSon® 53536
SkeeterRonnie 53057
facebook
Forum Stats
106138 Members
60 Forums
807423 Topics
10205024 Posts

Max Online: 36273 @ 01/23/13 02:34 PM
Topic Options
#11383417 - 02/01/16 08:48 AM installing a sandwich plate?
KLAPPER Offline
Angler

Registered: 09/10/15
Posts: 321
Loc: Jacksboro Texas
I just bought a Talon and I will be using a sandwich plate to install it to my lowe stinger, I have a 50hp mercury and I'm wanting to avoid taking it to the shop, has anyone ever installed one themselves? Any tips and tricks? Do I need to torque the bolts back to a certain spec? Any advice would be greatly appreciated
_________________________
www.Facebook.com/hellsgatebassclub


Top
#11383606 - 02/01/16 10:15 AM Re: installing a sandwich plate? [Re: KLAPPER]
gary purdy Offline
TFF Guru

Registered: 05/24/03
Posts: 11163
Loc: Littlefield Tx & Lake A. H. US...
Easy install
_________________________
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD

Top
#11383618 - 02/01/16 10:23 AM Re: installing a sandwich plate? [Re: KLAPPER]
Mike_Kelley Offline
Angler

Registered: 11/07/13
Posts: 499
Loc: Lake Fork, Texas (Wolf Creek)
Lower your motor, put a block of woof under the skag
loosen all motor bolts to the end, but only remove one side at a time. Put your bracket on and put the bolts back in, then repeat other side.

Top
#11385731 - 02/02/16 08:16 AM Re: installing a sandwich plate? [Re: KLAPPER]
steve@hydrodynamics Offline
TFF Celebrity

Registered: 08/25/06
Posts: 6770
Loc: Quitman,Tx
use a engine lift.
remove engine.
clean all silicone off transom
install new silicone ( i use 3m 4200)
install sandwich bracket.
install engine.
torque spec ? i tighten them till they don't move
_________________________
www.hydrodynamics-usa.com
903-763-5225





Top
#11388177 - 02/03/16 05:59 AM Re: installing a sandwich plate? [Re: steve@hydrodynamics]
John175 ® Online   content
Super Freak

Registered: 10/21/05
Posts: 65451
Loc: Realville
Originally Posted By: steve@scp
use a engine lift.
remove engine.
clean all silicone off transom
install new silicone ( i use 3m 4200)
install sandwich bracket.
install engine.
torque spec ? i tighten them till they don't move


^^^This

I rented an engine lift.
_________________________
Derek's Apprentice Key Master.
Keeper of the Keyz for the Keeper of the Beeez.

Top
#11390603 - 02/03/16 10:17 PM Re: installing a sandwich plate? [Re: KLAPPER]
Rubberdown Offline
Outdoorsman

Registered: 05/17/15
Posts: 162
Loc: Houston, Tx
Just so I have an idea, I'm about to ask about having this done at the shop tomorrow as I have no time to do it myself. I'm assuming they should charge a few hours labor?

Top
#11390710 - 02/03/16 11:52 PM Re: installing a sandwich plate? [Re: KLAPPER]
Flippin-Out Offline
Extreme Angler

Registered: 02/25/15
Posts: 1823
Loc: Magnolia, TX
I would think 2 hours tops, having taken engines loose before myself. (I own my own engine hoist, so no rental required.)

Top
#11391465 - 02/04/16 10:50 AM Re: installing a sandwich plate? [Re: KLAPPER]
steve@hydrodynamics Offline
TFF Celebrity

Registered: 08/25/06
Posts: 6770
Loc: Quitman,Tx
only takes 30 minutes or so to install.

if they are wiring the unit up also, then it will take longer.
_________________________
www.hydrodynamics-usa.com
903-763-5225





Top



© 1998-2017 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide