Forums59
Topics1,039,162
Posts13,960,194
Members144,192
|
Most Online39,925 Dec 30th, 2023
|
|
Getting side scan leveled out
#11271308
12/09/15 04:36 AM
|
Joined: Apr 2013
Posts: 429
John-Mark
OP
Angler
|
OP
Angler
Joined: Apr 2013
Posts: 429 |
Am I the only big guy out there? Lol I have my structure scan sonar mounted level on the transom ... Well when I'm alone ... 75% of the time... My boat "leans" a little to the right haha So when trolling around graphing I get a great right side image and [censored] on left side... Has anyone else set their structure scan off level to account for the lean? It's not a huge deal because I troll most of the time looking right anyways... But it would be nice to have equally as great an image on both left and right... However my right side image is so dead on I don't really wanna mess it up... Guess I could always load a couple of cases of water on my left side storage haha Just curious is all if anyone else has had this issue...
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11271315
12/09/15 04:42 AM
|
Joined: Dec 2008
Posts: 16,181
grout-scout
TFF Guru
|
TFF Guru
Joined: Dec 2008
Posts: 16,181 |
Nope, never had that problem. Maybe you need to put heavier junk on the opposite side of the boat to balance it. It would ride better too.
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11271358
12/09/15 05:26 AM
|
Joined: Jul 2014
Posts: 4,340
Bobby Milam
TFF Team Angler
|
TFF Team Angler
Joined: Jul 2014
Posts: 4,340 |
are you sure it isn't your engine being trimmed down causing interference? my boat leans but the left view on my screen is always from the motor
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11271367
12/09/15 05:50 AM
|
Joined: Apr 2013
Posts: 429
John-Mark
OP
Angler
|
OP
Angler
Joined: Apr 2013
Posts: 429 |
Hmm never thought of that? Gonna trim up next time out and report back Thanks for the tip it is mounted to the right of the motor so that makes sense
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11271711
12/09/15 02:37 PM
|
Joined: Jan 2013
Posts: 1,310
airforcefishin
Extreme Angler
|
Extreme Angler
Joined: Jan 2013
Posts: 1,310 |
^^ yep I have to trim up if I plan on using the left side
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11272197
12/09/15 05:42 PM
|
Joined: Jul 2007
Posts: 423
ifeliciano
Angler
|
Angler
Joined: Jul 2007
Posts: 423 |
Buy a cheap angle finder and with your boat in the water with you at the helm. Measure and record your bow to stern angle, and your port to starboard angle. When you go home put the angle finder back on the boat and adjust your trailer until the angles match the recorded angles done on the water. Once that is done, adjust your x-ducer to level.
GO ARMY!
|
|
Re: Getting side scan leveled out
[Re: ifeliciano]
#11272281
12/09/15 06:26 PM
|
Joined: Feb 2009
Posts: 45
1hoghunter
Outdoorsman
|
Outdoorsman
Joined: Feb 2009
Posts: 45 |
If you don't think too good don't think too much. Ted Williams
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11272342
12/09/15 07:17 PM
|
Joined: Jun 2008
Posts: 1,210
shotgunwilly
Extreme Angler
|
Extreme Angler
Joined: Jun 2008
Posts: 1,210 |
I guarantee you it's not the boat leaning causing the bad image. A slight angle like that wouldn't have a noticeable affect. Your engine or jackplate is probably interfering with the image if your transducer is on the right. You may have to lower the transducer.
Last edited by shotgunwilly; 12/09/15 07:18 PM.
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11273488
12/10/15 04:35 AM
|
Joined: Apr 2013
Posts: 429
John-Mark
OP
Angler
|
OP
Angler
Joined: Apr 2013
Posts: 429 |
Reporting back I trimmed up 1/4 and boom perfect image I could re mount but not a big deal.... Don't want more screw holes and it isn't any trouble Thanks guys i thought from looking that it was far enough down but I always look at my boat outside the trimmed up but trimming it all the way down it just barely gets in the way... Little touch on the trim and picture is great now Again thanks simple fix!
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11273495
12/10/15 04:38 AM
|
Joined: Jul 2011
Posts: 4,100
David Burton
TFF Team Angler
|
TFF Team Angler
Joined: Jul 2011
Posts: 4,100 |
Good Deal! Glad to hear you didn't have to change anything. Now, all you need is a jack plate, and you won't ever have to worry about it!
David Burton 2015 Skeeter FX 21 +Ultrex +Helix 12 (x3) +Mega360 +MegaLive
|
|
Re: Getting side scan leveled out
[Re: David Burton]
#11273498
12/10/15 04:40 AM
|
Joined: Apr 2013
Posts: 429
John-Mark
OP
Angler
|
OP
Angler
Joined: Apr 2013
Posts: 429 |
Good Deal! Glad to hear you didn't have to change anything. Now, all you need is a jack plate, and you won't ever have to worry about it!
|
|
Re: Getting side scan leveled out
[Re: John-Mark]
#11273531
12/10/15 05:14 AM
|
Joined: Jul 2014
Posts: 4,340
Bobby Milam
TFF Team Angler
|
TFF Team Angler
Joined: Jul 2014
Posts: 4,340 |
Glad to know it worked and you didn't have to take the drastic measure of losing weight.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|