Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
TLT, OnTheRoad, Scott Deischl, KcJordon, yankeedownsouth
105725 Registered Users
Top Posters
TexDawg 85933
hopalong 78097
Pilothawk 75038
JDavis7873® 67382
John175 ® 64788
FattyMcButterpants 60790
Derek 🐝 58257
Tritonman 57558
LoneStarSon® 53245
SkeeterRonnie 52975
facebook
Forum Stats
105725 Members
60 Forums
851686 Topics
12132847 Posts

Max Online: 36273 @ 01/23/13 02:34 PM
Topic Options
#11201275 - 11/02/15 09:24 AM evinrude trim manual release screw
Drawout Online   content
TFF Team Angler

Registered: 01/15/07
Posts: 3199
Loc: Paris Texas
79 evinrude manual release screw Apparently the threads are stripped because the screw will not tighten at all, is it a total loss or can these be retapped?

Top
#11201758 - 11/02/15 01:17 PM Re: evinrude trim manual release screw [Re: Drawout]
gary purdy Online   content
TFF Guru

Registered: 05/24/03
Posts: 11100
Loc: Littlefield Tx & Lake A. H. US...
Not likely. What motor?
_________________________
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD

Top
#11202163 - 11/02/15 04:58 PM Re: evinrude trim manual release screw [Re: Drawout]
Drawout Online   content
TFF Team Angler

Registered: 01/15/07
Posts: 3199
Loc: Paris Texas
The only pic I happened to have on my phone doesn't show much but the release screw is on the very right side




Top
#11202970 - 11/03/15 08:08 AM Re: evinrude trim manual release screw [Re: Drawout]
Tommy Yetts Offline
TFF Team Angler

Registered: 12/14/02
Posts: 3469
Loc: Rockwall, TX USA
I have never seen one stripped. Best bet would to find a good used trim system. What size motor is it?


Edited by Tommy Yetts (11/03/15 08:09 AM)
_________________________
Rockwall Marine
Tommy Yetts

www.rockwallmarine.com

Top
#11203001 - 11/03/15 08:22 AM Re: evinrude trim manual release screw [Re: Drawout]
gary purdy Online   content
TFF Guru

Registered: 05/24/03
Posts: 11100
Loc: Littlefield Tx & Lake A. H. US...
You might tap the area above the valve and put a short bolt on top of the valve to hold it down.
_________________________
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD

Top
#11203958 - 11/03/15 05:20 PM Re: evinrude trim manual release screw [Re: Drawout]
Drawout Online   content
TFF Team Angler

Registered: 01/15/07
Posts: 3199
Loc: Paris Texas
Its a 115 evinrude

Top
#11203974 - 11/03/15 05:29 PM Re: evinrude trim manual release screw [Re: Drawout]
Drawout Online   content
TFF Team Angler

Registered: 01/15/07
Posts: 3199
Loc: Paris Texas
Would the motor have to be in the up position to make the screw go back in maybe ? I didn't try that but just had it cross my mind but I'm not with the motor to check.

Top
#11205959 - 11/04/15 06:35 PM Re: evinrude trim manual release screw [Re: Drawout]
gary purdy Online   content
TFF Guru

Registered: 05/24/03
Posts: 11100
Loc: Littlefield Tx & Lake A. H. US...
No
_________________________
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD

Top
#11238820 - 11/22/15 06:08 PM Re: evinrude trim manual release screw [Re: Drawout]
Drawout Online   content
TFF Team Angler

Registered: 01/15/07
Posts: 3199
Loc: Paris Texas
Update on this issue I removed the unit from the motor planning to try and retap the threads and noticed the cclip was the only thing wrong with it, somehow it allowed the bolt out of it while the clip stayed on. I pulled the clip and the bolt tighten perfect then I put clip back on.

Top



© 1998-2017 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide