Forums59
Topics1,038,966
Posts13,956,550
Members144,184
|
Most Online39,925 Dec 30th, 2023
|
|
Help troubleshoot issue on an 04 225 HPDI
#11148265
10/06/15 03:48 PM
|
Joined: Feb 2009
Posts: 575
Over 10
OP
Pro Angler
|
OP
Pro Angler
Joined: Feb 2009
Posts: 575 |
Was out a couple of days ago and for abou an hour the engine ran like a stripped tail ape, Had to get a little gas at the marina and it ran fine for another 20 minutes. Pulling up to fish at my spot and at idle the engine died, started right back up but would only run at 1100 rpm's 1105 it would die. Had to do four miles to the ramp at 1100 but it made it with no warnings of any kind. What do you think? Bad gas? O2 sensor? Any thoughts would be greatly appreciated!
|
|
Re: Help troubleshoot issue on an 04 225 HPDI
[Re: Over 10]
#11148353
10/06/15 04:35 PM
|
Joined: Aug 2003
Posts: 362
CADD
Angler
|
Angler
Joined: Aug 2003
Posts: 362 |
Fuel filters, (HPDI's have a bunch) to learn a Ton about HPDI you can search a guy named RodBolt on iboats forum.
If your VST vapor separator filter gets clogged what you experienced can happen.
2001 Pathfinder 2200V 150Vmax HDPI 2015 Diablo Amigo (Sand Fleck)
|
|
Re: Help troubleshoot issue on an 04 225 HPDI
[Re: CADD]
#11148825
10/06/15 08:43 PM
|
Joined: Jun 2008
Posts: 1,210
shotgunwilly
Extreme Angler
|
Extreme Angler
Joined: Jun 2008
Posts: 1,210 |
What would it do when you pushed down on the pedal? Did it feel really rough and wouldn't get over 1100?
I have the same engine and had an issue with a bad TPS (Throttle Position Sensor) so when it was in gear the engine would think it was in neutral and wouldn't be running on all cylinders.
|
|
Re: Help troubleshoot issue on an 04 225 HPDI
[Re: Over 10]
#11149882
10/07/15 01:25 PM
|
Joined: Dec 2002
Posts: 3,826
Tommy Yetts
TFF Team Angler
|
TFF Team Angler
Joined: Dec 2002
Posts: 3,826 |
Did you check the primer bulb, was it hard or soft?
|
|
Re: Help troubleshoot issue on an 04 225 HPDI
[Re: Over 10]
#11155674
10/10/15 03:15 PM
|
Joined: Feb 2009
Posts: 575
Over 10
OP
Pro Angler
|
OP
Pro Angler
Joined: Feb 2009
Posts: 575 |
Willy, when I pushed the pedal it would just die and not go over 1100rpm though it would start right back up. Tommy, the primer bulb was hard as a rock.
|
|
Re: Help troubleshoot issue on an 04 225 HPDI
[Re: Over 10]
#11155675
10/10/15 03:16 PM
|
Joined: Feb 2009
Posts: 575
Over 10
OP
Pro Angler
|
OP
Pro Angler
Joined: Feb 2009
Posts: 575 |
Thank you CADD I'll have a look.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|