Main Menu
Advertisement
Affiliates
Advertisement
Newest Members
BorderBassBattle, Trisha d'Fisha, Bperez, Strokn88lx, Maverickoutdoorstx
103156 Registered Users
Top Posters
TexDawg 83688
hopalong 74987
Pilothawk 73816
JDavis7873® 67378
John175 ® 61087
FattyMcButterpants 60592
Tritonman 57173
Derek 56843
SkeeterRonnie 52571
LoneStarSon® 52419
facebook
Forum Stats
103156 Members
62 Forums
865493 Topics
11361754 Posts

Max Online: 36273 @ 01/23/13 02:34 PM
Topic Options
#10961049 - 07/07/15 07:54 AM Transom Savers for Evinrude 200hp - Can't find one to fit
dandeeks Online   content
Angler

Registered: 04/06/14
Posts: 298
Anybody out there with an old Evinrude care to share what kind of transom saver they are using and where to get it? I have tried 2 already. I have a '95 200Hp Evinrude Vindicator(2stroke). I tried the transom saver that Academy sells, and though it works and fits... it is not long enough and the motor hangs too close to the ground. I was told that "Motor Stiks" are what I should get, since they are "universal"... those did not end up actually fitting. I even tried to strip it with a bit to make it wider to get the fit but was not successful.

Can anyone chime in on this? Surely someone on here must have gone through this same experience?



Edited by dandeeks (07/07/15 08:06 AM)

Top
#10961134 - 07/07/15 08:37 AM Re: Transom Savers for Evinrude 200hp - Can't find one to fit [Re: dandeeks]
Big Kev Offline
Outdoorsman

Registered: 03/20/15
Posts: 72
In my experience it is not the motor type that dictates the length of your transom saver rather the boat / trailer model. Sounds like you have a Ranger. I have a 2005 Ranger and had to go to a Ranger dealer in order to get one long enough. Not sure what boat brand you have but I would contact a dealer with that brand.

Top
#10961233 - 07/07/15 09:17 AM Re: Transom Savers for Evinrude 200hp - Can't find one to fit [Re: dandeeks]
dandeeks Online   content
Angler

Registered: 04/06/14
Posts: 298
That makes sense to me... I actually have a '95 Stratos. I will take your advice and get in touch with Stratos and ask them.
Thanks and much appreciated Big Kev.

Top
#10962224 - 07/07/15 04:29 PM Re: Transom Savers for Evinrude 200hp - Can't find one to fit [Re: dandeeks]
Rhino Ranger Offline
Angler

Registered: 05/19/08
Posts: 381
Loc: tx hays county
I actually took a new one to a welder(one that can tig weld aluminum)
and had him cut it in half and add about 2ft of aluminum square tubing to it. I have the one that runs from the motor to the trailer.
_________________________
P.B 10lb 14oz. Sam Rayburn P.B. 5 43lb 11oz Falcon

Top
#10962275 - 07/07/15 04:55 PM Re: Transom Savers for Evinrude 200hp - Can't find one to fit [Re: dandeeks]
Dubee Online   content
Extreme Angler

Registered: 07/17/11
Posts: 1254
Loc: Godley Tx
Just go buy tubing and cut the lenght you need.

Top



© 1998-2016 OUTDOOR SITES NETWORK all rights reserved USA and Worldwide