Forums59
Topics1,038,962
Posts13,956,462
Members144,184
|
Most Online39,925 Dec 30th, 2023
|
|
In need of suggestions
#10867242
05/24/15 02:22 AM
|
Joined: Mar 2012
Posts: 171
Dean74
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Mar 2012
Posts: 171 |
I have a 95 Mercury xri 200 2.5! The problem occurred about a month ago took it to my mechanic (A good one at that). The boat idles and planes off great as well as midrange up to 3800 rpm's! The problem is when you hit 3900 rpm's the boat bogs down if you back off to 3800 it runs perfect again. Here's a list of what's been done since the problem started. ECU REBUILT BY CDI NEW FIBER REEDS INSTALLED(found one chipped) FUEL PRESSURE TESTED HIGH SIDE AND LOW SIDE (3 times) EVERY IGNITION COMPONENT TESTED DRAINED THE FUEL ADDED NEW Anyone else run into a similar problem?
|
|
Re: In need of suggestions
[Re: Dean74]
#10867818
05/24/15 10:01 AM
|
Joined: Nov 2006
Posts: 2,848
TLW
Extreme Angler
|
Extreme Angler
Joined: Nov 2006
Posts: 2,848 |
what is tha number of tha ecu?.. should be 823003 1 or A 1... why was ecu "rebuilt"?.. does your mech have access to a known good/untouchrd ecu?.. CDI is 0 and 3 on rebuilt ecu's that I actually know of!.. lots more through network connections.. were tha injectors/fuel rail o-rings serviced/replaced?.. does it die if ya don't back out of it?...was tha low pressure mech. pump checked?...
Last edited by TLW; 05/24/15 10:10 AM.
|
|
Re: In need of suggestions
[Re: Dean74]
#10868017
05/24/15 01:27 PM
|
Joined: May 2003
Posts: 11,586
gary purdy
TFF Guru
|
TFF Guru
Joined: May 2003
Posts: 11,586 |
I have hit problems with the motor wiring harness on these boats. That fuel pressure needs to be tested while on the water.
The world will not be destroyed by those who do evil, but by those who watch them without doing anything. Remember what He has done and remember that He is not done yet!-- GOD IS GOOD
|
|
Re: In need of suggestions
[Re: Dean74]
#10868040
05/24/15 01:39 PM
|
Joined: Sep 2010
Posts: 1,599
boatwhisperer
Extreme Angler
|
Extreme Angler
Joined: Sep 2010
Posts: 1,599 |
Need to test the detonation control module. It allows an 8 degree timing advance if the engine is not detonating. Could be malfuntcioning... Or it could be working correctly and it is sensing engine problems
boatwhisperer
|
|
Re: In need of suggestions
[Re: Dean74]
#10869230
05/24/15 10:22 PM
|
Joined: Mar 2012
Posts: 171
Dean74
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Mar 2012
Posts: 171 |
Thanks for the replies! The number on the ecu is 824003 A8 and it was rebuilt because the mechanic thought that might be the problem so it was sent to cdi to be tested and they said it tested bad and sent me another rebuilt one in its place. It does not die if you stay in it just bogs down.yes the low pressure pump was tested as well as the high on the water running at normal operation. Boatwhisperer thanks I will have that checked
|
|
Re: In need of suggestions
[Re: Dean74]
#10869737
05/25/15 02:04 AM
|
Joined: Nov 2006
Posts: 2,848
TLW
Extreme Angler
|
Extreme Angler
Joined: Nov 2006
Posts: 2,848 |
best thing ta do with tha det. sensor and module on an older motor is trash it.. if you take it out again put in fresh plugs.. run it around till its good and warm.. throttle it down and let it bog down a few minutes then shut it off with tha key whiles its "boggin'.. immediately pull tha plugs and take a look.. justa note.. jus cause CDI says its good ta go don't make it so.. ie: A8 is a '96 200 ecu, first year with tha pump inside tha silver vst....is yours that type or is tha pump outside tha vst? reason I asked is that there is a small cone shaped filter in tha "U" shaped hose on tha bottom of tha pump that gets over looked a lot and can cause problems....
side note... its always a "second guess" when ya ona computer but its ideas from lotsa folks on here that have seen a lot over tha years....gl
Last edited by TLW; 05/25/15 02:40 AM.
|
|
Re: In need of suggestions
[Re: Dean74]
#10869958
05/25/15 03:31 AM
|
Joined: Mar 2012
Posts: 171
Dean74
OP
Outdoorsman
|
OP
Outdoorsman
Joined: Mar 2012
Posts: 171 |
TLW mine is the one with the pump outside the VST and yeah I have already checked that as well as the filter near the schrader valve.I agree there is lots of knowledge right here in TFF. After reading everyone's input and researching the ECU numbers and detonation control module I really think one of the 2 is where my problem lies. I really appreciate all the input and I will keep all of you updated on this and what it ends up being hopefully it will help someone else in the future.
|
|
Re: In need of suggestions
[Re: Dean74]
#10870129
05/25/15 05:20 AM
|
Joined: Nov 2006
Posts: 2,848
TLW
Extreme Angler
|
Extreme Angler
Joined: Nov 2006
Posts: 2,848 |
justa a little fyi.. if you can get hold of ANY 824003 ecu. 150, 175, 200 all tha way up ta tha A30 it will work fine for testin'.. truth be known there's not much difference in any of 'em.. found that some 150's run better on 200's than tha 150's.. some 200's run better on 150's/175's and such...fuel maps/circuitry seem ta be a little inconsistent at best..'specially tha early 003's. gl!
Last edited by TLW; 05/25/15 05:51 AM.
|
|
Moderated by banker-always fishing, chickenman, Derek 🐝, Duck_Hunter, Fish Killer, J-2, Jacob, Jons3825, JustWingem, Nocona Brian, Toon-Troller, Uncle Zeek, Weekender1
|